







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Door Installation in Westview, FL: What the Job Actually Involves
Door installation in Westview usually runs one to two days for a single exterior or interior door, and $650 – $2,400 installed depending on the door, the frame condition, and permit scope. A standard pre-hung entry door sits near the low end; a custom-sized door in an older concrete-block wall with new framing, a security-rated slab, or a rolling-code opener system pushes toward the top. Call (833) 716-6251 and we’ll walk your opening, measure it, and hand you a written line-item price.
How We Run a Door Installation, Stage by Stage

Most of the door jobs we take on in Westview aren’t a clean swap. They’re a door going into a wall that’s been sitting since the 1950s or 60s, sometimes with an old jalousie or single-pane unit still in the opening. Here’s the sequence, and where you make decisions.
Stage 1: Opening assessment and measurement (day 1, 60 – 90 minutes)
We pull the trim, check the rough opening, and confirm the wall is square and the header is sound. On a concrete-block wall this is where we find out whether the block is plumb or whether the old frame was shimmed to hide a lean. You’ll also confirm here whether the door is a like-for-like replacement or a change in size, because that decision drives everything after it.
Stage 2: Demo and prep (day 1, 2 – 4 hours)
The old door and frame come out. We inspect for rot, old termite damage, or a failed sill pan, and we repair the framing before anything new goes in. This is the stage nobody budgets for and everybody needs: a door hung over a soft sill will leak. You decide at this point whether to add a longer sill pan or step up to a heavier threshold.
Stage 3: Setting and shimming (day 1 into day 2, 2 – 3 hours)
The new unit gets set, shimmed, and checked for square, plumb, and smooth swing. We screw through the hinge jamb into the framing, not just the trim, which is what keeps a door from sagging in a humid climate. This is the stage where we also confirm the hardware and opener rough-in if you’re going with a powered or rolling-code system.
Stage 4: Sealing, flashing, and trim (day 2, 3 – 5 hours)
South Florida rain finds every gap. We flash the head and jambs, seal the sill, and reinstall or replace trim. Exterior doors get a proper weather seal at the bottom, not a bead of caulk that fails in a season. You decide the finish here: paint, stain, or a factory-prehung exterior that arrives sealed.
Stage 5: Hardware, adjustment, and final walk (day 2, 1 – 2 hours)
We install locksets, deadbolts, closers, and any powered opener or remote, then adjust the strike plate and swing. If a permit was pulled, we schedule the inspection. We walk the door with you, demonstrate the hardware, and hand over the spec sheet.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Options You’ll Choose Between
- Door material: Steel entry doors are the durable, low-maintenance pick and hold up well to humidity. Fiberglass looks like wood, resists dents, and costs a bit more. Solid wood is beautiful and needs real maintenance in this climate. Aluminum works for some slider and security applications.
- Pre-hung vs. slab: A pre-hung unit (door already in its frame) is faster and usually cheaper to install. A slab door reuses the existing frame and only makes sense if the frame is solid and square, which is often not the case in older Westview block homes.
- Security rating: A standard residential door, a reinforced strike-plate door, or a full impact- and burglar-rated system. Security doors add real peace of mind and hold up to forced entry better, at a higher cost.
- Powered vs. manual hardware: Rolling-code remotes and powered openers matter on garage doors and some security doors. Rolling-code means the remote signal changes every time, which closes the gap that older fixed-code remotes leave open.
- Finish and hardware: Paint, stain, brushed nickel, matte black, or a factory finish. Hardware grade affects both look and durability.
What Door Installation Costs in Westview, FL

For a single door, most Westview homeowners land between $650 and $2,400 installed. Here’s the range broken out by type, and then what pushes a job from one end to the other.
- Interior door: $250 – $700 installed.
- Standard exterior entry door: $650 – $1,400 installed.
- Security or reinforced entry system: $1,200 – $2,800 installed.
- Powered or rolling-code opener hardware (garage or security door): $400 – $1,200.
- Custom-sized door in a block wall: $1,500 – $3,500 installed.
Four things move that number. First, the size and whether it matches a standard opening. A cut-in in concrete block costs more than a like-for-like swap. Second, the condition of the wall and frame. Rotted sills, missing headers, or an out-of-square opening add demo and framing time. Third, the material grade. Steel and fiberglass are the value picks; wood and custom finishes cost more and need more care here. Fourth, the permit scope. A simple replacement in the same opening may not need a permit; a change in size or a new opening does, and that adds inspection time.
Our written estimates list the door, hardware, flashing, trim, labor, and permit line separately. What’s typically excluded: painting or staining beyond a bare seal, stucco patching around a changed opening, and any structural repair found after demo. You’ll see those as change orders before we touch them, not after. A free estimate visit is the fastest way to a real number.
See the difference
Before
After
Before
After
Before
AfterWhat Westview Homes Specifically Do to This Job
Westview (ZIP 33167) isn’t a greenfield suburb. It’s an older, working-class community where a 1950s or 60s concrete-block home with original jalousie windows and a flat membrane roof often sits right next to a new duplex going up. On many blocks, a contractor pulling permits will find additions that were built without records, so scope and permit history get verified before we touch a door opening. That’s the first thing we do on an infill block: check what’s actually been added.
The climate drives the rest. South Florida’s summer thunderstorms and June-through-November hurricane season mean a door has to be wind-rated and properly flashed, not just hung. Humid conditions affect how caulk and finish cure, so we schedule sealing work for a dry window. We also see more door problems on homes where an unrecorded addition changed the wall line, which is where an out-of-square opening shows up.
Serving Westview, FL – Our Local Coverage Area
We serve Westview and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked: Door Installation in Westview

Most single-door jobs take one to two days, with interior doors done in a single day. A custom opening in a concrete-block wall or a job that turns up hidden framing damage can run longer, and you’ll know the revised timeline before we start. Call (833) 716-6251 to schedule your estimate.
It depends on the scope. A like-for-like replacement in the same opening often doesn’t require one, but a change in size, a new opening, or a wind-rated door that needs a signed and sealed product approval usually does. We pull the required permits and handle the inspection. Call us and we’ll tell you which side of the line your job falls on.
Usually yes. As long as the new door fits the existing opening and the header is sound, there’s no plumbing or structural work involved. If the door is wider than the current frame, that’s when framing changes enter, and we’ll price that in the estimate.
A security-rated or reinforced entry system typically lands between $1,200 and $2,800 installed, and rolling-code opener hardware adds roughly $400 to $1,200. The higher end reflects impact rating, custom sizing, or both. Call (833) 716-6251 for an exact quote; estimates are free.
Every door installation we do in Westview is covered by the 730-Day Done Right Promise: if it isn’t done right, we make it right. That covers workmanship for two full years, and our technicians have up to 12 years of experience on the install side.
Get a Free Door Installation Estimate in Westview
A door that’s hung square, sealed right, and backed in writing is the whole job. Call (833) 716-6251 to schedule a free on-site estimate for Door Installation in Westview. We’ll measure the opening, walk you through your material and security options, and hand you a written line-item price with no surprises. Customers often pair this with Cabinets & Countertops in Westview or a Garage Conversion ADU in Westview for a bigger scope. If door work is part of a Windows & Doors in Westview project or our broader Windows & Doors service, we’ll fold it into one estimate.
Written by the team at Groundwork Construction Co.












